pl en de fr es it


Styrofoam 3D panel "OLD BRICK"

A novelty on the European market of interior finishing!


Decorative panel calculator Have a question?
Write to us



3d See 3D rotating photo
Styrofoam decorative 3D panels imitating new brick, old brick, slate stone. Here we present a Styrofoam panel imitating the OLD BRICK. Polish Product.

The panel has been designed to be easy to install and there are no visible dividing lines as is the case of typical rectangular or square panels.

The panel is made similarly to Styrofoam ceiling tiles, which can be painted with any colour of acrylic paint.

Panels are installed to the wall with Styrofoam glue, which can be purchased in any construction store. The best way to install panels is to buy Styrofoam glue in tube. Then, the dirt will be kept to a minimum. The adhesive is applied directly to the back of the panel and glued to the wall. After drying, the panels should be painted on any colour. More information can be found in the product card that can be downloaded here.

The vast advantage of the panels compared to gypsum panels available on the market is their LOW WEIGHT and that they are EASY TO TRANSPORT. One panel weighs only 140 grams. The weight of panels to cover a wall of 15m2 is only 9kg! Bringing the panels home and up to the floor is no effort.

Panels have dimensions of 44.6 cm x 59.4 cm and thickness of about 2.5 cm; a dozen square meters of a wall can be covered in a few hours without even getting dirty (tube glue)! Panels can be freely cut with a wallpaper cutter.

Gallery of completed projects

We would like to show you the photos of several selected projects completed by our customers. We encourage you to share your work with us as well!

Annas_Barber_Shop #2 Annas_Barber_Shop
agnieszka #2 agnieszka
andrzej #2 andrzej
anzela #2 anzela
artur #2 artur
bartek #2 bartek
bogusia #2 bogusia
celina #2 celina
damian #2 damian
dariusz #2 dariusz
dorota #2 dorota
ewelina #2 ewelina
jakub #2 jakub
janusz #2 janusz
joanna #2 joanna
kamil #2 kamil
kamila #2 kamila
karol #2 karol
kasia1 #2 kasia1
kasia2 #2 kasia2
kasia3 #2 kasia3
kasia4 #2 kasia4
lilia #2 lilia
lucyna1 #2 lucyna1
lucyna2 #2 lucyna2
lukasz1 #2 lukasz1
lukasz2 #2 lukasz2
magda #2 magda
malgorzata #2 malgorzata
marcin #2 marcin
marcin1 #2 marcin1
marcin2 #2 marcin2
marek #2 marek
mirka #2 mirka
ola #2 ola
pawel1 #2 pawel1
pawel2 #2 pawel2
pawel3 #2 pawel3
piotr #2 piotr
przemek #2 przemek
tomek #2 tomek
tymon #2 tymon
weronika #2 weronika
zenon #2 zenon
zuzanna #2 zuzanna
 

See more photos from the gallery


 

Panel technical data sheet

Download a technical drawing

Technical parameters:

Height: 44.6 cm
Width: 59.4 cm
Thickness: 2.5cm
Weight of 1 panel: 0.14 kg
Material density: 35kg/m3 +/- 5% (Styrofoam hardness is similar to boards or ceiling rosettes)
Material: EPS (Styrofoam) for construction, self-extinguishing.

Packaging

Panels are packed in foil bags of 4 pcs which is 0.92m2.
Bulk packaging contains cartons measuring 80x60x45cm. In one carton there are 8 packs of 4 pcs., total of 7.36 m2.

Purpose and scope of application

DECORTENA decorative panels are intended for indoor use. Installation of panels to walls or ceilings is done by using commercially available adhesives for Styrofoam. It is recommended to use glue in tube, which provides convenient applying on the panel and then installing to the wall or ceiling. Products are not resistant to organic solvents such as acetone, nitro compounds, petrol, etc. Do not install panels near heat sources.

Installation instructions

Apply a layer of glue to the smooth surfaces of the panels' contact with the substrate. The substrate, on which the panel will be installed, should be even, dry, free from dust and grease. When installing panels on paint coatings, peel off the paint as well as cracked and fallen plaster. Large surface defects must be filled with spackling paste so that the contact point of the panel with the substrate is smooth.

Installation of decorative panels

EPS decorative panels allow great freedom of interior design due to easy cutting of shapes with a wallpaper cutter. Panels can be installed in fragments forming protruding motifs on a smooth wall or cover a whole or larger area. To cover the entire surface of the wall, start with one of the corners and arrange the panels in parallel rows. Before installing the first panel, cut off the protruding elements to get a straight vertical edge.

Apply the adhesive only to the back of the panel. When gluing, press the panel firmly, while paying attention to not damage the decorative surface. Panels are designed for painting with water-based paints.

Storage, transport, safety

Products should be transported and stored in manufacturer's packaging, stored in rooms away from sources of open flames or high temperatures. Each bulk packaging is labelled with at least the following information: manufacturer's name and address, trade name, product symbol.

The product does not require special precautions. The product is not intended for children. Products are recyclable.

Orders

The minimum order is 4 pieces of panels.